• Slide-in solution
    • Adjustable solution
    • Piling solution
    • Ballast solution
    • Shingle Roof
    • Thin-film stick solutihon
    • Sheet metal clamp solution
    • Hanger bolt solution
    • Rectangle clamp solntion
    • Click-in solution
    • Hook solution
    • This solution is suitable for open field system and flat roof system with ram post or concrete foundation. The installation efficiency can be doubled by sliding the modules into the rails.
      This solution is highly compatible as it can be applied in thin film modules and crystalline modules. Wind load is 60m/s, and snow load is 1000N/㎡.
      Advantages:
      1．The installation efficiency is doubled as there are no clamps needed.
      2．The screw bolts can be adjusted so as to cater to framed modules, frameless modules and thin film modules.
      3．The plastic washer within the rails is to protect the modules.
      4．The height of the mounting system can be adjusted.
      5．This solution is suitable for open field system and flat roof system.
    • One can change the panel's tilt angle by moving the attach point of the back support on the slide rail, granting a better geographical adaptability.
      Ballast system, surface anodized, applied to flat roof and solar farm. The system can withstand load equal to 60m/s wind velocity and 1000N/ ㎡snow load.
      Advantages:
      1．The inclination of the modules can be adjusted.
      2．Material: Al
      3．Anodizing surfacing
      4．Non-penetrathon to roof
    • Tilt adjustable solution is suitable for flat roof system and open field system with concrete foundation. The racks are fastened onto the concrete foundation by means of connecting components.
      This kind of solution is highly accepted because of the advantage of maintaining an optimal tilt angle to optimize output. System of this solution bears the wind load higher than 60m/s and snow load of 1000N/㎡.
      Advantages:
      1．Suitable for flat roof systems and open field systems
      2．Material-AL
      3．Arch-shaped connecting components
    • The Ballast solution is suitable for flat roof system and open field installations. A special aluminum wind deflector plus the EPDM profile at the bottom greatly reduced the wind load exerted on the solar panel, granting the ability of withstanding the load equal to 60 m/s wind velocity.
      Adjacent solar panels could share the tray/plate and the rail, saving the materials and making the installation convenient. The surface of the profile is galvanized. Snow load is 1000N/㎡.
      Advantages:
      1．Wind safe deflector
      2．EPDM profile
      3．Ballast tray/ plate
      4．Surface galvanize
      5．Integrated design
      6．Applied to most of flat roof and ground systems
    • Special fastening solutions ensure water-proof of the system. The wind load is 55m/s, snow load is 900N/㎡.
      Advantages:
      1．Special foundation
      2．water-proofing gasket.
      3．less material.
    • Thin film modules can be stick to the metal strip with silica gel. This solution is suitable for roof system and thin film modules. The wind load is 55m/s, the snow load is 900N/㎡.
      Advantages:
      1．Close distance to roof surface, ensuring the stability of the system.
      2．Materials can be reduced significantly.
      3．Invisible line design.
      4．Non-penetration to the roof, which is 100% water-proof.
    • The Sheet metal clamp solution is suitable for trapezoidal sheet metal roofs with standing seams. In this kind of solution, a so called standing seam clamp is applied to fasten the cross beam of the racks onto the sheet metal roofs.
      The clamp is customized according to the individual trapezoidal sheet metal form. The system bears the wind load higher than 55m/s and snow load of 900N/㎡.
      Advantages:
      1. Customized sheet metal clamps made of stainless steel
      2．Without any penetration to the sheet metal roof so as to ensure 100% water-proof
      3．Quick installation
      4．Wide choice to cater to individual trapezoidal sheet metal form.
    • It is suitable for tile roof and metal sheet roof. A hanger bolt with EPDM sealant and a racking plate are used. The hanger bolt is screwed into the substructure through the roof cladding. The racking plate bears the weight of the rails.
      The load is therefore transferred from the mounting system to the substructure by the hanger bolt. The system bears the wind load higher than 55m/s and snow load up to 900N/㎡.
      Advantages:
      1. Special gasket
      2．Hanger bolt made of 304 stainless steel
      3．Convenient for transportation
      4．Suitable for all kinds of sheet metal roof and plain tile roof
    • Suitable for trapezoidal roof. The special clamps directly attached to the standing seams. With large attach area, the pressure exerted on the sheet metal is reduced.
      Convenient installation. Surface anodized, which provide aesthetic and anti-corrosion. Wind load up to 55m/s velocity, snow load 900N/㎡.
      Advantages:
      1．Unique design of the Japanese style clamps
      2．Disperse the pressure
      3．Suitable for all kinds of trapezoidal roof
      4．ED surfacing
    • The modules can be fastened by just clicking the clamps into rails, so as to improve the installation efficiency tremendously.
      This solution is suitable for thin film modules and crystalline modules. The wind velocity is 55m/s and above, and the snow load, 900N/m2.
      Advantages:
      1．High installation efficiency.
      2．This solution is suitable for thin film modules.
      3．This solution can be applied to modules with different thickness.
    • Hook solution is suitable for pitched roof. The major material is stainless steel. Usually two horizontal cross beam supports one line of module in this kind of pitched roof.
      The hooks are fastened onto the substructure by means of screw bolts. And another end bears the cross beam of the mounting systems. The hooks can be adjusted to cater to tiles with different thickness.
      The advantage of this solution is that the system can be 100% water-proof without any penetration tothe roof.
      Advantages:
      1．Roof hook made of stainless steel
      2．Variety choices of hooks
      3．Adjustable hooks to cater to tiles with different thickness
      4．Non-penetration to tiles so as to ensure 100% water-proof
      5．Stable and light weight.
    • Single support ballast solution
    • Single support precast solution
    • Adjustable easy-in solution
    • Two support precast solution
    • Ballast solution
    • The single support ballast mounts are a heavy duty mounting solution for small area PV needs. They support pole diameters of 70 to 90 mm and modules from most manufacturers.
      The big screw can be drive directly into the ground without pre-foundation. Those mounts are manufactured using hot-dip galvanized steel.
      Advantages:
      1．Single support
      2．Wide range of ram post meeting all kinds of geographic demands
      3．Special design of fastening
      4．Material: hot-dip galvanized steel
    • Single-support solution can be divided into precast solution and ballast solution. Single support is used to bear the whole system so as to reduce land occupancy, which is more environmental-friendly.
      Meanwhile, The system bears the wind load higher than 60m/s and snow load of 1000N/㎡.
      Advantages:
      1．Single support
      2．Quick Mounting On Concrete Foundation
      3．Special design of fastening
      4．Material: hot-dip galvanized steel
      5. Installed without affecting the ground beneath.
    • This solution is suitable for open field system and flat roof system with ram post or concrete foundation. The installation efficiency can be doubled by sliding the modules into the rails.
      This solution is highly compatible as it can be applied in thin film modules and crystalline modules. Wind load is 60m/s, and snow load is 1000N/㎡.
      Advantages:
      1．The installation efficiency is doubled as there are no clamps needed.
      2．The screw bolts can be adjusted so as to cater to framed modules, frameless modules and thin film modules.
      3．The plastic washer within the rails is to protect the modules.
      4．The height of the mounting system can be adjusted.
      5．This solution is suitable for open field system and flat roof system.
    • Adjust your tilt angle to optimize output. In an open field system an inclined strut is needed that tilts the module up to an optimal angle (usually 30 degrees) and faces the correct way.
      The inclined strut can be built of galvanized steel or aluminum, and is attached to the support. The inclined strut is manually tilt adjustable, so that in winter when the sun is lower in the sky the cells can be tilted up for greater exposure.
      Advantages:
      1．Two supports.
      2．The inclination of modules can be adjustable.
      3．A variety of ram post meets all geographic demands.
      4．Material: hot-dip galvanized steel.
    • The Ballast solution is suitable for flat roof system and open field installations. A special aluminum wind deflector plus the EPDM profile at the bottom greatly reduced the wind load exerted on the solar panel, granting the ability of withstanding the load equal to 60 m/s wind velocity.
      Adjacent solar panels could share the tray/plate and the rail, saving the materials and making the installation convenient. The surface of the profile is galvanized. Snow load is 1000N/㎡.
      Advantages:
      1．Wind safe deflector
      2．EPDM profile
      3．Ballast tray/ plate
      4．Surface galvanize
      5．Integrated design
      6．Applied to most of flat roof and ground systems
    • one-side carport
    • Double-side carport
    • There is six-meter-length sunshade area, which is suitable for all modes of private cars. The design of invisible lines has been adopted to protect the power units.
      The surface treatment of anodizing guarantees a relatively long life span of the system. The system can withstand load higher than 60m/s wind velocity and snow load of 1000N/㎡.
      Advantages:
      1．Hard firm design
      2．Anodizing surfacing
      3．Sunshade area with the length of six meters
      4．Invisible line design
    • In this system, two supports are used to support one unit of the mounting systems. Anodizing surface. The system can withstand load higher than 60m/s wind velocity and 1000N/㎡ snow load.
      Advantages:
      1．Two supports
      2．Anodizing surfacing
      3．Sunshade area with the length of six meters
      4．Invisible line design
    • Shingle roof system
    • Ram post
    • Tile roof
    • Component details:
      1．Aluminum mounting round block : 39mm*39mm
      2．Aluminum flashing : 1.5mmthick, 304mm*304mm
      3．M8 Hanger bolt: 152mm
      4．Stainless steel and EPDM rubber sealing washer
      5．M8 hex nuts
      6．Stainless steel flat washer
    • Currently, PV ground-mounted system solutions include concrete foundations, ram posts, ballasts. integrated,etc.
      The ram post is embedded into then ground,and acts as a support for the whole system. This solution covers a relatively small area. Depending on geological conditions, the ram post may be a C-shape, ∑-shape,and earth screw. The first tow shapes are applied to flat ground with sandy. or day soils. The earth screw is more flexible and is applied to flat ground with rocky soils.